giftsa.blogg.se

1. #Raspberry pi samba windows 7 how to
2. #Raspberry pi samba windows 7 install
3. #Raspberry pi samba windows 7 update
4. #Raspberry pi samba windows 7 android
5. #Raspberry pi samba windows 7 password

But first, we create a backup (just in case): sudo cp /etc/samba/smb.conf /etc/samba/smb.conf_backupĪdd the following section to the end of the file and save with CTRL + O. We create a new folder in the previously mounted directory: mkdir /media/usb/share Of course, it is also possible to save the files on the SD card of the Raspberry Pi. The files can either be located directly on the hard drive or in a subdirectory. Save with CTRL + O and exit the Nano Editor with CTRL + X. The following line must be added to the end of this file (with the correspondingly adapted UUID) UUID= 9678-B72E /media/usb vfat auto,nofail,noatime,users,rw,uid=pi,gid=pi 0 0 To do this, execute the following command: sudo nano /etc/fstab This is recommended because it can happen that the Raspberry Pi has to be restarted. One last point is the automatic mounting. We mount the device: sudo mount /dev/sda1 /media/usb -o uid=pi,gid=pi

Now we create a new folder (you can also create it somewhere else) that points to the contents of the storage device and give our user (pi) ownership rights to it: sudo mkdir /media/usb In my case, the UUID is 9678-B72E, which is shown under sda1. If you see multiple devices, you can run the command again when the hard drive is not connected and then compare. We then need the UUID of the device, which we can find out as follows: ls -l /dev/disk/by-uuid/ Mount the External Storage Device on the Raspberry Piįirst of all, the hard drive must be connected via USB (ideally to the USB 3.0 port).

#Raspberry pi samba windows 7 how to

Answer yes.īefore we go on to the actual configuration, let’s take a look at how to use an external hard drive as a storage medium. You will be asked whether the settings should be used by DHCP.

#Raspberry pi samba windows 7 install

Then we install Samba: sudo apt-get install samba samba-common-bin

#Raspberry pi samba windows 7 update

To do this, open an SSH terminal and enter the following: sudo apt-get update Install and Configure the Raspberry Pi Samba Serverįirst, we bring the package sources up to date. In addition, these are usually cheaper than small 2.5 inch external hard drives.

Since the Raspberry Pi can only deliver limited power via the USB 3.0 port, a hard drive with an external power supply is recommended.

#Raspberry pi samba windows 7 android

The integration of a Samba server is very easy under Windows 10, Mac, Linux as well as Android and iOS. This means that the files are not stored with third-party providers, and the transfer speed is also much higher. If the data is only needed at home by several PCs, a Raspberry Pi Samba server is ideal: There is a central network storage device that all other devices can access while on the same network. However, these are usually stored in an online service, and not everyone wants that. This has the advantage that the files can be accessed from anywhere. In it the "pihome" folder will be the folder you've shared.More and more data is being stored in the clouds. If you select "Network" in windows explorer device "RASPBERRYPI" should be found (it may take a minute or two to appear).

#Raspberry pi samba windows 7 password

If you want to permit read only access change writeable to "No"įinally add the pi user by typing this command and entering the pi's password twice: Search for the workgroup line (normally at the top) and if necessary set it to match your workgroup (if you don't need it set then it can just be left as default, works fine for us not changed)īelow it you'll find the wins support line, if there is a # at the start of the line remove it to stop it being commented out and then ensure it is set to "yes", so you should have:Īdd a section at the bottom which contains the settings for the share:Ĭhange path as required ( "path=/" is fine if you want access to the entire drive). Samba contains the SMB protocol, support for the Windows naming service (WINS), and support for joining Windows workgroups. Samba-common-bin contains a tool that you'll need to register users with Samba. Sudo apt-get install samba samba-common-bin The following instructions will set your RPi to share its files on your local network and be accessible by Windows.